How To Cut Pvc Pipe Without A Saw 4 Best Ways

Do you need to cut a PVC pipe but don’t have a saw? Don’t worry – there are several ways to do it without one. In this blog post, we’ll show you how to cut pvc pipe without a saw using a hacksaw, a jigsaw, and a drill. We’ll also show you how to use a deburring tool to smooth the edges of your cuts. So whether you’re a beginner or an experienced DIYer, we’ve got you covered. Keep reading for instructions on how to cut PVC pipe like a pro!

1. Cut Your PVC Pipe with String!

This method doesn’t actually involve using a saw. Instead, it uses the weight of the pipe itself to break through the surface and create an even divide between your sections.

PROCEDURE:

          Stretch string tightly across the length of your PVC pipe at least twice for greater strength. Tie each end into loops that can be easily used to hang the pipe up by.

          Suspend your PVC pipe from a sturdy support beam or sturdy rafters in your work area using rope, wire, zip ties or whatever you have available. This will act as the weight that will eventually sever your pipe once it’s fully suspended.

Note: make sure there’s nothing flammable or explosive near your work area.

2. Use a PVC Cutter to Cut PVC

PVC cutters are designed to make short work of cutting schedules, hard pipes and fittings. These tools allow you to put your weight into it and maximize your leverage for powerful cutting. Although they aren’t the only way to cut PVC, this is by far the most efficient method. Not only is it fast, but the resulting cut is clean and burr-free.

PROCEDURE:

          Clamp your PVC in a vise. A C-clamp placed at the end of your pipe will hold it securely so you can get to work.

Fit your pvc cutter onto the pipe and turn it to tighten.

          Keep turning until you feel a pop and see that the pipe has broken in two pieces.

           Remove the pieces of PVC pipe and separate them, leaving your new cut on one side of the cutter and the cut-off pieces on the other.

3. How to Cut PVC With a Jigsaw

A jigsaw is another popular tool for cutting hard and schedule 40 PVC pipes, but it’s most effective when used with a straightedge or guide of some sort. You can use anything from scrap wood to plumbing fittings for this purpose, but make sure whatever you’re using is the same thickness as your pipe.

PROCEDURE:

          Clamp your guide to your work surface so that your PVC pipe is held tightly in place.

Secure your jigsaw blade into its holder, and then connect it to your jig saw.

Press the blade of your jigsaw against the edge of your guide as close as possible to where you want to cut.

          Pull the trigger on the jigsaw’s handle, keeping a firm grip on the saw as it begins to cut through your pipe.

           Once your jigsaw has broken through the surface of your pipe, remove both pieces from your work area and separate them. Be sure to discard or recycle any off-cuts that have been created by this process.

4. Use a PVC Pipe Cutter for Curved Cuts

The easiest way to cut a pipe that has a curve is the use a PVC Pipe Cutter. You can buy these from your local hardware store or online.

PROCEDURE:

          Clamp your PVC pipe in a vise so that it’s held tightly in place.

Secure your cutter onto the pipe, and then tighten it until it touches both sides of the pipe.

          Spin the cutter around the circumference of your pipe, creating a seal that will hold the blade in place.

           Tighten the knobs on each side of your cutter until it breaks through and severs the pipe.

5. How to cut PVC with a hacksaw

Hacksaws are great for cutting ABS or soft PVC – not so much for hard or schedule 40 PVC. Because of this, we recommend using a hacksaw only in the few cases where you don’t have access to another tool. However, if that’s your only option, go for it.

PROCEDURE:

          Cut a piece of PVC pipe that is longer than the length you need. It may sound counterintuitive, but this will make your life easier when you cut the pipe in half . Trust us on this one!

(Optional) Mark where you want to cut the pipe using a pen or marker. You can also score the pipe using a utility knife. This will create a groove where you cut, which reduces the amount of force required to break the pipe.

Secure one end of your pipe in an open vise (you can improvise with tools like wrenches or pliers), free hand grip it firmly at the other end, and then press the hacksaw blade into the PVC as close to your mark as possible.

Remember to push forward on the saw – don’t pull back! This reduces friction on the blade and prevents it from overheating or binding up so you can make a smooth cut.

           Continue sawing until you’ve reached your mark. Repeat until you’ve cut all the way through your pipe.

Engage a deburring tool to remove any rough edges from your PVC cuts, and then sand down any jagged areas. (Optional) Adhere PVC primer to the cut edge of burrs with a fine-grit sandpaper. In addition, consider using heat shrink tubing over rough cut ends to protect against potential scratches or injuries.

Cut PVC pipe using the drill and knife method

Cutting PVC pipe with a drill (or any kind of power saw) is best for thicker schedules or more rigid applications, such as structural members.

PROCEDURE:

          Clamp your PVC pipe into a vise . If you have a second set of hands, that’s great; if not, you can use a C-clamp to secure the pipe in place.

           Rather than trying to cut through the pipe all at once, you’ll use a rotary tool to make a groove in the PVC. If you don’t have a Dremel, you can use a rotary file or even a regular drill.

           Use your tool to cut an initial groove into the pipe. Make it as wide as the blade of your tool and about 4 to 5 inches deep (or more, depending on the thickness and rigidity of your pipe).

           Use a handsaw to cut through the remainder of your PVC. This should be much easier than trying to cut the pipe in one pass.

conclusion:

Cutting PVC is relatively easy, as long as you pay attention to how you’re doing it. We recommend using a hacksaw for curved cuts, a PVC pipe cutter for straight cuts, and a rotary tool with a blade or bit to remove chunks of plastic. Remember to use clamps to secure the pipe in place, and wear eye protection or a dust mask (if you’re using power tools).

If you follow these tips for how to cut pvc pipe without a saw, you should have no trouble getting your plumbing needs met. Good luck!

FAQ’s:

What is the best way to cut PVC pipe?

The best way to cut pvc pipe depends on the type of material you’re working with and what kind of cuts you’re making. For example, if you need to make a very precise cut for your plumbing pipes or just want to save some time, a pvc pipe saw is best. However, if you’re cutting larger sections in half or don’t want to buy a specific tool, a hacksaw will do the trick.

Can you use PVC pipe to make rain gutters?

Yes, but using pvc piping for gutters is not ideal. Using a standard pvc pipe, there’s a risk of the pipes falling off and making a big mess. However, you can use a flexible pvc pipe (or another type of piping) to make gutter sections. These sections fit together and snap on securely; they also don’t need to be supported by brackets.

How do you cut PVC pipe?

The most efficient way to cut pvc pipe is with a manual cutter. This gets the job done quickly and with little effort. For thicker pipes (or those that will be holding a significant amount of weight) you should use a power saw like a rotary saw. If easy access isn’t a concern, you can also use a hack saw or handsaw.

What is the best size pvc pipe for drainage?

The size of pvc pipe you use for drainage will depend largely on what you’re trying to do with it. For example, if you’re using it to drain water from your sump pump , the size will be smaller than if you were using for sewer.

Do pvc pipes emit harmful chemicals?

The type of pvc pipe you’re using and the quality of your installation will determine whether or not it emits harmful chemicals. For example, pvc pipes that release lead into the water supply are not allowed to be used in residential buildings. However, PVC drainage piping that has been properly installed by a licensed professional typically does not cause any problems.

How do you fix pvc pipe?

If your pvc pipe has a crack or even if the water is leaking out of it, you can use PVC primer and cement to repair. This will help seal leaks and give you the ability to make seamless repairs.

How do you seal pvc pipe?

You can use PVC primer and cement to seal leaks in your pvc pipe. This product will help you make a complete and watertight seal.

How do you make pvc pipe smooth?

If your pvc pipe is rough, it might not be compatible with certain fittings or end caps. To make your pipe smooth, you can use a rotary tool to file down the surface of the pipe.

What does pvc pipe weigh?

PVC is lightweight but still strong enough to hold up under pressure. This makes it a great option for all kinds of plumbing and drainage projects.

How does pvc pipe work?

PVC pipe is a great option because it’s durable and easy to install. This makes it useful for homes and businesses all over the world.

What is polyvinyl chloride (pvc)?

Polyvinyl chloride or PVC is a plastic material that is commonly used to make pipelines, drainage pipes and fittings. PVC has a high tensile strength, flexible design and versatility that makes it easy to use in commercial or residential settings.